Sunday, 27 July 2014

Growth and Development of a Cotton Plant


The cotton plant has perhaps the most complex structure of all major field crops.  Its indeterminate growth habit and extreme sensitivity to adverse environmental conditions is unique.  The growth of the cotton plant is very predictable under favorable moisture and temperature conditions.  Growth follows a well-defined and consistent pattern expressed in days.  Another useful and more precise way to assess crop development relies on using daily temperatures during the season to monitor progress (Table 1).  The heat unit concept utilizes accumulated hours above a critical temperature rather than calendar days in describing growth and development.  The growing degree days (DD) concept is based on a developmental threshold above which the crop grows.  Below that temperature is where little or no development occurs.  For cotton, the threshold temperature is 60˚F; therefore, the degree days are referred to as “DD60’s”. The basic formula for calculating heat units involves averaging the maximum and minimum temperatures for each day and subtracting the threshold temperature.  Calculation of the accumulated heat units and knowledge of the heat unit requirement for any particular growth stage can be used to explain and predict the occurrence of events or duration of stages in crop development (Kerby et al., 1987; Landivar and Benedict, 1996; Oosterhuis, 1990).
Table 1. The average number of days and heat units required for various growth stages of cotton in the Mid-South.
Growth Stage
Days
Heat Units – DD60s
Planting to Emergence
4 to 9
50 to 60
Emergence to First Square
27 to 38
425 to 475
Square to Flower
20 to 25
300 to 350
Planting to First Flower
60 to 70
775 to 850
Flower to Open Boll
45 to 65
850 to 950
Planting to Harvest Ready
130 to 160
2200 to 2600
Modified from Oosterhuis, 1990
Stages of Growth
The developmental phases for cotton can be divided into five main growth stages:  (1) germination and emergence (2) seedling establishment (3) leaf area and canopy development (4) flowering and boll development and (5) maturation (Fig. 1).  The transitions between these stages are not always sharp and clear.  Each stage may also have different physiological processes operating within specific requirements.  If producers are aware of these stage-dependent differences in cotton growth and requirements, then many problems in crop management can be avoided, which will result in higher yields and profits.


growth-fig-1
Figure 1. Seasonal development of cotton in the Mid-South with a May 1 planting date, showing typical production patterns of squares, bolls and open bolls (Oosterhuis, 1990, with permission ASA).
Root Development
Under favorable germination conditions, the radicle (root) emerges within two to three days.  The radicle becomes the taproot that grows downward into the soil.  The taproot penetrates the soil rapidly after germination and may reach a depth of up to 10 inches or more by the time the cotyledons unfurl (5 to 7 days, 50 DD60s) (Fig. 2).  Root development during the early vegetative stage may proceed at the rate of 0.5 to 2.0 inches per day, depending on soil temperature and moisture conditions (Huck, 1970; McMichael, 1986). 
growth-fig-2 
Figure 2.  Stages of germination and seedling emergence (Oosterhuis, 1990, with permission ASA).
The roots may be 3 feet deep in some soils when the above ground portion of the plant is only about 14 inches (Fig. 3). The taproot may penetrate the soil from less than 1.5 feet to as much as 9 feet while the lateral roots remain fairly shallow, less than 3 feet (McMichael and Quisenberry, 1993). On deep alluvial and irrigated soils in California, roots reach a depth of 3 to 4 feet when the young plants are only 8 to 10 inches high, with a final depth at maturity of 9 feet (Grimes et al., 1972).  The bulk of the root system is located in the upper 3 feet, but this is dependent upon the soil moisture, soil physical structure and vigor of the individual plant (Taylor and Ratliff, 1969; Pearson et al., 1970; Taylor and Gardner, 1983).  The total root length continues to increase as the plant develops until the maximum plant height is achieved and fruit begins to form.  Total root length begins to decline as older roots die.  Furthermore, root activity begins to decline as the boll load develops and carbohydrates are increasingly directed toward developing the fruit (McMichael, 1986).
growth-fig-3

Figure 3.  Early-season root development of cotton (Oosterhuis, 1990, with permission ASA).
Vegetative Development
Under favorable conditions for germination, cotton seedlings emerge five to ten days after planting or after 50 to 60 DD60s are accumulated.  The fully expanded cotyledons are 1 to 2 inches above the soil surface and are arranged directly opposite the main stem.  The cotton plant has a very prominent main stem, which results from the elongation and development of the terminal bud or apical meristem.  The main stem consists of a series of nodes and internodes and has an indeterminate growth habit (Fig. 4).  Much of the early development of the cotton plant is directed by the development of a substantial root system while growth of the first true leaves is relatively slow.  The number of nodes and the length of the internodes are influenced by genetics and environmental factors such as climate, soil moisture, nutrients, disease and insects.  The appearance of a new node for relatively non-stressed cotton occurs after an additional accumulation of 50 to 60 DD60s (Kerby et al., 1987; Oosterhuis, 1990).
 
growth-fig-4
Figure 4.  The basic structure of a cotton plant includes the main stem, which is made up of a series of nodes and internodes, and two types of branches, vegetative and fruiting branches (NCC, 1996).
The developmental rate of a new node is significantly slower when the plant is water stressed.  Typically this produces shorter stature plants.  Nodes give rise to main stem leaves and branches.  Main stem leaves and branches are spirally arranged on the stem in a three-eighths phyllotaxy above the cotyledonary node.  Two types of branches are produced: monopodial are the vegetative branches and sympodial are the fruiting branches.  Monopodial branches are structurally similar to the main stem.  Growth is from a single terminal bud and tends to grow in an upright position.  Sympodial branches are produced by the main stem and monopodial branches and grow at an acute angle to the main stem.  Every sympodial branch has a main stem leaf associated with the branch. As the branch extends from the main stem, each new fruiting node has an extending leaf and a fruiting structure or square at each node.  Elongation of the internode behind the flower bud and leaf causes them to extend away from the main stem.  The development of this branch terminates in a square, but a second leaf and square develop in the axil of the first leaf and similarly extend away from the first leaf and square by internode elongation.  Repetition of this process produces several squares and leaves resulting in the typical zigzag appearance of the fruiting branch.  The flowers are opposite the leaves on the sympodial branches and develop more rapidly than monopodial branches.
Final plant height is also a function of the extension of main stem nodes. Within cotton varieties, the seasonal total numbers of main stem nodes is strongly influenced by determinacy and growing environment. Cotton breeding and selection for earliness has favored shorter statured, more determinant cotton varieties. However, management factors such as excessive nitrogen fertilizer and excessive square loss from insect feeding can cause even moderate stature plants to grow excessively tall and rank (Siebertet al. 2006).
Reproductive Development
Signs of reproductive growth begin to appear about four to five weeks after planting with the formation of the floral buds or squares in the terminal of the plant (Table 1). Cotton has a distinctive and predictable fruiting pattern. Once fruiting begins, fruiting branches tend to be produced at each successive main-stem node. The first fruiting branch is often produced at the sixth or seventh node on the main stem. Approximately three days elapse between fruit on a given fruiting branch and the same relative position on the next higher branch. The time interval for the development of two successive fruiting forms on the same sympodial branch is approximately six days (Fig. 5). Squaring is followed about three weeks later by flowering and the start of boll development. The time requirement for a square to develop into a white flower is not influenced significantly by external conditions or plant stress. Throughout the remainder of the season, the cotton plant, due to its indeterminate growth habit, will continue adding vegetative growth at the same time as the reproductive development. The occurrence of the first position white flower moves closer to the terminal of the plant as the developing bolls become the major sink for photosynthate, which in turn also results in the slowing of new node or square development (Robertson et al., 2007a).
Table 2. Timing of various events during square development relative to the flowering date of an individual fruiting structure.
Days
Before
Flower
Size of Bud
Comments
40
Microscopic
Square initiation can occur as early as 2nd true leaf expansion.  Hot weather induces four-bract squares, cool weather delays square initiation.
32
Microscopic
Lock numbers determined.  Carbohydrate stress decreases number from 5 to 4.
23
2 mm PHS
Ovule number determined.  Carbohydrate stress decreases potential seed number.
22
2 mm PHS
Pollen cells divide.
19
3 mm MHS
Pollen viability reduced by high nighttime temperatures.
5
13 mm
Squares start expanding rapidly
3
17 mm
Fibers begin to form
0
Flower opens White flower
Pollen sheds and fibers start to elongate.  Extremes of humidity or water disrupts pollen function.

Modified from Stewart, 1986
growth-fig-5
Figure 5. Expected flowering interval in days beyond first flower illustrating the three day age difference in flowering dates of the same fruiting position on the next higher fruiting branch and the six day difference in age between fruiting positions on the same branch (Oosterhuis, 1990, with permission ASA).
The boll develops rapidly after fertilization and reaches its full size within three weeks (Fig. 6).  An additional four to five weeks are required for boll maturation.  Seeds attain their full size about three weeks after fertilization, but do not reach maturity until shortly before the boll opens.  Fibers attain their full length in about 25 days after fertilization with the maximum growth rate occurring during the first 10 to 15 days of this period.  Thickening of the fiber begins at about 16 days after fertilization and continues until the boll is mature.
growth-fig-6
Figure 6. Although bolls are full size 21 days after flowering, fiber and seed development requires an additional 28 to 35 days (NCC, 1996).
Fiber thickening occurs by the daily deposition of consecutive layers of cellulose on the inner wall of the fiber in a spiral fashion.  The degree of thickening and the angle of the spirals affect fiber strength and maturity.  Fiber elongation and maturity can be impacted by numerous factors from fertilization to maturity (Table 3).  Until the boll opens, the fiber is a living cell, but upon opening the fiber is exposed to the air and soon dries out and becomes twisted (Seagull, 2001).  In addition to the long fibers, most commercial cultivars (excluding Gossypium barbadense) have very short white or colored fibers on the seed called linters or fuzz fibers.
Days
After
Flower
Event
Primary Factors Influencing the Event
-2 to 12
Fiber density on seed surfaceTemperature and carbohydrate status
0
Pollen shedTemperature and relative humidity
0 to 3
Rate of fiber initiationTemperature and potassium status
0 to 3
Pollen tube growth and seed fertilizationTemperature and relative humidity
1 to 14
Boll abscissionPlant water and carbohydrate status
3 to 25
Fiber length and seed numberTemperature and potassium status
15 to 45
Fiber cellulose (fiber thickening)Temperature
25 to 50
Protein and oil accumulationTemperature, plant water, nitrogen and potassium status
49 to 50
Boll openingTemperature and relative humidity


Table 3. Timing of various events during boll development relative to flowering and primary factors influencing the event.
Cotton quality is defined by the length, maturity, strength and micronaire of the fiber.  These qualities are determined by the genetic makeup of specific plant varieties, the climatic conditions experienced by the crop, and the management of the crop through production and harvest (Table 4).  For example, bolls maturing late in the season, when temperatures are lower, require a longer period for fiber growth and development and usually produce less lint often of lower quality.
Fiber Quality Parameter
 Genetics
%
 Environment
%
Staple
 82
 18
Micronaire
 41
 59
Color
 21
 79
Strength
 90
 10


Table 4. The degree of variability in fiber quality parameters as influenced by the genetic makeup of the variety and the environment (weather and management) during the growing season (NCC, 1996).
The relative importance of the fruiting positions oriented from the main stem along a sympodial branch varies, i.e., the first, second and third sympodial positions contribute about 60, 30, and 10 percent of the total seed cotton yield, respectively (Bednarz et al., 2000; Jenkins et al., 1990).  The lint quality tends to also decrease away from the main stem.  The likely production problems occurring during the maturation stage include low temperatures and slow upper-canopy boll development, which can increase boll rot, delay harvesting, reduce the efficacy of defoliants and boll openers, and lower quality lint.
The growth and development of the cotton plant follows a typical sigmoid curve with a relatively slow start during emergence and root growth, followed by an exponential increase in growth rate during canopy formation, flowering, boll development and slowing down during the boll maturation phase (Fig. 7).  Both genotype and environment affect this pattern.  Nevertheless, a general and predictable pattern of growth exists for the cotton plant (Hearn, 1994, Jones and Wells, 1997).
growth-fig-7
Figure 7. The growth and development of the cotton plant follows a typical sigmoid curve (NCC, 1996).
Understanding cotton growth and development is critical in order to implement sound management strategies for maximum yields and profits.  Cotton is a perennial plant with an indeterminate growth habit and has a very dynamic growth response to environment and management.  Site-specific management strategies need to be taken into consideration to optimize yields.  Furthermore, management strategies should be flexible to allow for changing environmental conditions.

Copied from http://www.cotton.org/tech/ace/growth-and-development.cfm 

Friday, 6 June 2014

Different types of woven fabric

Woven Fabrics

Woven fabrics are made by using two or more sets of yarn interlaced at right angles to each other. Much variety is produced by weaving. Woven fabrics are generally more durable. They can be easily cut into different shapes and are excellent for producing styles in garments. However the raw edges ravel or fray easily and need to be protected. Fabrics having more fabric count (number of wrap and weft yearns present) keep the shape well. Low count fabrics are less durable and may snag or stretch.
Woven fabrics are manufactured in different widths depending on the end use. The fabrics used for apparels usually contain 90 cms width. The Sheeting materials are generally made having a width of 160 cm/140cms and 150cms/180 cms.

Woven Fabric Types

Buckram

It is a stiff coated fabric made from a light weight loosely woven fabric, impregnated with adhesives and fillers. This fabric is used as interfacing so as to provide support and shape rentention to necklines, collars, belts, cuffs, waist bands, button closures etc in garments. They are also used as reinforcements for hand bags and other articles.

Cambric

Cambric a light weight fabric woven in plain weave and produced with a stiff finish. It is suitable for women's dresses and children's dresses that require crispness.

Casement

Casement is a medium weight cotton fabric made of closesly packed thick warp yarns. Generally it is used for curtains, tablelinen, upholstery and rarely used for dresses.

Cheese Cloth

It is popular light weight sheer fabric having open weave. It has a low count fabric consisting of carded yarns. Originally it was used for wrapping cheese or meat and hence the name. It is neither strong nor durable. It is finished in a variety of ways that attract the consumer. It is used not only for women's and children's dresses but also for drapery fabrics. Due to its open structure, it does not require much ironing.

Chiffon

Chiffon fabrics are sheer, light weight fabrics made of hard twisted yarns. Originally these are made in silk fabrics but today they are made from rayon or polyester. They are used for sarees and women's evening wear. The fabrics encounter with the problem of shrinkage.

Chintz

Chintz is a medium weight, plain woven cotton yarn. It is often given a glazed finish which may be temporary or semi permanent glazed chintz are available in solid colour as well as printed with floral prints. These are often made from blends of cotton and polyester or rayon. They are used for skits, dresses, blouses, pyjamas, aprons and draperies.

Corduroy

It is a cut pile fabric available in solid colours. The cut pile fibres are seen in the form of ribs on the surface. It is mainly used for pants, jeans and shirts.

Crepe

A silk fabric is originally characterised by a crinkle, puckered surface formed by highly twisted yarns in the warp or weft or both. By using ordinary yarns similar crepe effects can also be produced. Synthetic fabrics also impart crepe effect finish. It is used for sarees, shirts, women and children's dresses.

Denim

It was traditionally a yarn dyed, warp faced cotton twill fabric. Warp is usually coloured (mostly blue, maroon, green and brown) and weft is white. This fabric is made of two weights for sports wear and overalls. It's use as jeans has made it very popular and so the nature of denim is also changed to suit the trend. It is often napped, printed and made with stretch yarn.

Drill

It is a warp faced twill woven fabric. It has a stiff finish. Originally it was produced in white and now it is available in solid colours. It is mairly used for pants, knickers and uniforms.

Flannel

Flannel is a woollen fabric woven in plain or twill weave having characteristic soft handle. It looks like a bulky fabric due to the milling that is usually done to this fabric. Flannel fabric is used for suits and pants and infacnt's clothing.
This fabric is popular as cleaning fabric due to its extreme softness. This is also used to protect children from cold atmosphere.

Gabardine

Gabardine is a closely woven, clear finished warp faced twill fabric. It contains more number of warp yarns than weft yearns and also more durable. It is usually woven in 2/1 or 2/2 twill and has a raised diagonal twill effect on the right side. It largely used for rain coats, suitings and sports wear.

Georgette

Georgette is a sheer light weight fabric, woven in plain weave. It has a characteristic rough texture produced by hard twisted ply, yarns both in warp and weft. Originally it was made in silk, but today it is produced in rayon and polyester too.
It's mainly suitable for women's evening wear.

Kashmir Silk

Kashmir silk is a silk fabric produced in plain weave and is either embroidered or printed. The motifs used are characteristic of Kashmir. It is used for shirts, women's wear and sarees. Kashmir shawls are woven in twill weave and is usually embroidered with traditional Kashmiri embroidery.

Khadi

Khadi is a term used to a wide variety of fabics that are hand spun and hand woven. They are produced in mainly one cotton fibre, blends of two or more fibres. They are known for durability, and simplicity. The fabrics can be suitings dhoties overalls and household textiles.

Lawn

Lawn is a fine sheet, light weight, crisp fabric either made in cotton or linen. Various finishes are given to this fabric, in which the fabric is called by the name of the finish. It is mainly used as lining in dress.

Mulmul

It is an Indian term generally applied to fine cotton fabric slightly heavier, than muslin. These are often printed fabrics. They find use as sarees.

Muslin

Muslin is a light weight open cloth of plain weave. It may be used as grey or bleached and dyed. It is used as household textiles and dress materials.
Organdy
Originally it is a lawn fabric which is given a stiff finish. Acid is used for this finish to make the fabric transparent and stiff. It is mainly used for women's wear.

Poplin

Poplin is a medium weight, cotton fabric hving a fine weft rib. it is generally used for shirting, dresses and upholstery.

Sheeting

These are primarily used for bed coverings. They are medium weight, closely woven fabrics woven eigther in plain or twin weave. Sheeting fabrics are made in different widths. High quality cotton sheetings are made in plain weve with a width of 64" x 58" and in twill weave with a width of 60"x72".

Taffeta

Taffeta is a smooth, crisp, transparent fabric having a fine rib. Originally it is made with silk fibres but now it is also made in rayon. It has a characteristic finish which produces crispness. It is used as women's evening wear.

Tissue

It is a fine fabric either made in silk or man made fibre. They are characteristically interwoven with gold or silver threads. It is produced in rich colours and they are used as women's dress material, sarees etc.

Velvet

It is a warp cut pile fabric, originally made from silk. It is also produced in Rayon. The dense cut pile makes it very soft and lustrous. It is used as dress materials for women and children. It is also produced with special high twisted yarns which are single or ply yarns. Based on the yarns used and twist given, they are named as semi violes (single yarns1x1) full voiles. (ply yarns 2x2) or half voile (double in warp and single in weft 2x1).

Sunday, 11 May 2014

Denim Finishing


4189182611 3e3dff6555 o Denim Finishing
Denim is one of the oldest fabric, but still, it is one of the most fashionable and widely used fabric. And as the full jeans trend is going wildly this season, we can have a deeper look at the finishing details of your jeans. And somehow, denim has the most sophisticated finishing. Some of the techniques found below can be done by yourself, like bleaching, washing and ripping.

Acid Washing

4189943186 054b253eba o Denim Finishing
Patented in 1986, this wash uses pumice stones soaked in bleach to create deep contrast within the coloring of the denim jeans.

Batching

4189942890 d622e91501 o Denim Finishing
We can find this in many kidswear jeans and old school jacket. As Denim is a durable fabric, the batch is attached on the surface firmly.

Bleaching

4189181599 f55d8f8e23 o Denim Finishing
A chemical used to make denim fade. Liquid bleach is usually an aqueous solution of sodium hypochlorite, and dry powdered bleaches contain chloride of lime (calcium hypochlorite).

Crushing

4189942314 8f32fd2b79 o Denim Finishing
A textured effect achieved through a special fabric construction and wet processing. The denim jeans are woven with an overtwisted weft yarn; when the garment is washed, the yarn “shrinks,” acquiring a goffer look that is further enhanced by bleaching and stonewashing.

Dirty Washing

4189181103 e8f4a9e61a o Denim Finishing
A finish that creates the look of stained jeans.

Embroidered

4189180683 9c250b1bce o Denim Finishing
Found in many high-end denim in Japan. You can see the insanely details done by the Japanese, to replace the printing.

Frayed

4189180141 60b33cb378 o Denim Finishing
A finish in which the waistband and hems of denim jeans have been sanded to create a “worn” effect.

Overdyed

4189179993 7870c5fbb8 o Denim Finishing
A second dying process executed after denim jeans have been sewn, to make the thread color the same as the jean.

Raw

4189939578 6a06387ea5 o Denim Finishing
Denim jeans that has been not been treated or finished.

Screen-printing

4189940518 009518d973 o Denim Finishing
The majority of denim is 100% cotton and very good for screen printing.

Sandblasting

4189940176 cfc7f681ec o Denim Finishing
A laundry process in which denim jeans are shot with guns of sand in order to make the jeans look as if they’ve been worn.

Tearing and ripping

4189178965 871380ebc5 o Denim Finishing
Denim jeans that have purposely been ripped or teared — and not repaired — prior to sale.

Tinted

4189178767 a31337343c o Denim Finishing
Denim jeans that have been dyed a second time, usually with a yellow khaki hue, to create the look of vintage denim.

Washing

4189941346 3050e69b77 o Denim Finishing
The are several washing method:
Enzyme wash – Considered a more efficient and environmentally sound way to stone wash jeans. Rather than using pumice stones, organic enzymes (proteins) are used that eat away at the indigo. Jeans finished using enzymes tend to be stronger than those broken down by traditional stone washing, as the fabric is not subjected to the same level of abuse.
Sand wash – A finish achieved through a combination of pumice stones, enzymes and sand; used to create the illusion of aged denim jeans.
Stone wash – A process that physically removes colour and adds contrast. A 20 yard roll of fabric, generally 62 inches in width, is put into a 250-pound washing machine along with pumice stones. The fabric and stones are rotated together for a set period of time.

Whiskered

4189939254 1a5a23c1f6 o Denim Finishing
A denim jeans finish that produces white lines that look like wrinkles near the crotch and sometimes behind the knees.
If you have any other treatment you have done to your jeans, please leave comments.

Thursday, 3 April 2014

Unimix by Rieter

UNIMIX HOMOGENEOUS MIXER - EFFECTIVE MIXING IN A MINIMUM OF SPACE

The B 72 / B 76 mixing machine guarantees homogeneous, intimate mixing of the bale feed in a minimum of space, even with unfavorable bale lay-down. The unique 3-point mixing process is equally suitable for cotton and man-made fibers. Eight mixing chambers ensure not only effective mixing, but also high production performance. The large storage volume of the UNImix provides the ideal preconditions for a high degree of operating autonomy in the blowroom.

Economy

  • The production volume of 800 kg/h (B 72) or 1 200 kg/h (B 76) results in an excellent price/performance ratio with comparably low space requirements.
  • The large storage capacity ensures regular feeding of the downstream blowroom machines and is the precondition for the production of quality yarn without personnel intervention.
  • Settings are entered rapidly, easily and reproducibly on the UNImix by the push of a button. Short setup times result in high efficiency.

Quality

  • The unique 3-point mixing principle with 8 mixing chambers produces a good, permanently homogeneous fiber mix. This is the precondition for consistently high yarn quality.
  • Tuft size can be adjusted at the mixing roller in coordination with raw material and application; optimal opening and homogeneous feed to the subsequent process are thus guaranteed.
  • Integrated dust removal separates the dust-laden conveying air from the fiber material. This occurs extremely gently and consequently improves the running behavior of the spinning machine and thus also yarn quality.

Flexibility

  • The easy addition of an opening or cleaner module provides flexibility with the capability to respond to changes in market conditions.
  • The ability to process cotton, blends and man-made fibers means that there are no limitations when processing different raw materials.
  • Bypass facility for the cleaner module (e.g. with man-made fibers) for rapid mix change.

Machines used for Short stable spinning

Table 1 - Machines used in short-staple spinning

Wednesday, 2 April 2014

History of Natural and Man made Fibers

Fiber History
Natural fibers have been used for apparel and home fashion for thousands of years, with the use of wool going back over 4,000 years. In comparison, the man-made fiber industry began with the first commerical production of rayon in 1910.
For those old enough to remember the 50's and 60's, this was when there was a great deal of technology happening in the man-made fiber industry. And the technology continues even today. Microfibers, fibers finer than the finest silk, were developed in 1989 and lyocell, was developed in 1993. Today, many man-made fibers, including polyester have been developed into beautiful fabrics that are being used by major designers.

Natural Fibers
History of the principal natural fibers used in textiles for apparel and home fashion
EST. DATE
FIBER
BACKGROUND AND PRODUCTION
5,000+ BC
FLAX:
  • Generally considered to be the oldest natural textile fiber.
  • Fine linen was used as burial shrouds for the Egyptian pharaohs
  • Largest producer: Soviet States; other large producers include Poland, Germany, Belgium and France. Largest exporters are Northern Ireland and Belgium.
3,000+ BC
COTTON:
  • Earliest use estimated between 3,000 BC to 5,000 BC.
  • Worn by Egyptians earlier than 2,500 BC.
  • Eli Whitney's invention of the cotton gin in 1793 revolutionized the processing of cotton.
  • The development of the power loom in 1884 brought significant improvements and variations to cotton fabrics.
  • Major producers: United States, Soviet States, China and India. Lessor producers include Pakistan, Brazil, Turkey, Egypt, Mexico Iran and Sudan.
3,000 BC
WOOL:
  • Used by people of the Late Stone Age,
  • There are 40 different breeds of sheep, which produce approximately 200 types of wool of varying grades.
  • Major producers include: Australia, New Zealand, Soviet States, China, South Africa, and Argentina.
2,600 BC
SILK:
  • Believed discovered by a Chinese princess.
  • Silk is made from two continuous filaments cemented together and used to form the cocoon of the silkworm.
  • Silk culture began about 1725 BC, sponsored by the wife of China's emperor.
  • Secrets of cultivation and fabric manufacturing were closely guarded by the Chinese for about 3,000 years.
  • There is a story that two monks smuggled seeds of the mulberry tree and silkworm eggs out of China by hiding them in their walking sticks.
  • India learned of silk culture when a Chinese princess married an Indian prince.
  • The major producer and exporter of silk is Japan.

MAN-MADE FIBERS

The history of U.S. Production of the principal man-made fibers used in textiles for apparel and home fashion
It is important to understand that all manufactured fibers are not alike. Each fiber has a unique composition and it's own set of physical properties. The U. S. Federal Trade Commission has established generic names and definitions for manufactured fibers, including acetate, acrylic, lyocell, modacrylic, nylon, polyester, polypropylene (olefin), rayon, and spandex. However, all fibers under a generic name are not exactly the same.
Fiber producers have been able to modify the basic composition of each generic fiber, both chemically and physically, to produce variations which provide a softer feel, greater comfort, brighter/longer lasting colors, better warmth/cooling, moisture transport/wicking, and better properties for blending with other fibers. These improved fibers are given a trademark name and are owned and promoted by the fiber producer. The following is a list of producers of manufactured fibers and their trademark names.
DATE
FIBER
FIRST COMMERICAL PRODUCTION
1910
RAYON
  • The first man-made fiber.
  • The first commercial production of rayon fiber in the United States was in 1910 by the American Viscose Company.
  • By using two different chemicals and manufacturing techniques, two basic types of rayon were developed. They were viscose rayon and cuprammonium rayon.
  • Today, there are no producers of rayon in the U.S.
1924
ACETATE:
  • The first commercial production of acetate fiber in the United States was in 1924 by the Celanese Corporation.
1939
NYLON:
  • The first commercial production of nylon in the United States was in 1939 by the E. I. du Pont de Nemours & Company, Inc. It is the second most used man-made fiber in this country, behind polyester.
1950
ACRYLIC:
  • The first commercial production of acrylic fiber in the United States was in 1950 by E. I. du Pont de Nemours & Company, Inc.
1953
POLYESTER:
  • The first commercial production of polyester fiber in the United States was in 1953 by E. I. du Pont de Nemours & Company, Inc.
  • Polyester is the most used man-made fiber in the U.S.
1954
TRIACETATE:
  • The first commercial production of triacetate fiber in the United States was in 1954 by the Celanese Corporation.
  • Domestic Triacetate production was discontinued in 1985.
1959
SPANDEX:
  • The first commercial production of spandex fiber in the United States was in 1959 by E. I. du Pont de Nemours & Company, Inc.
  • It is an elastomeric man-made fiber (able to stretch at least 100% and snap back like natural rubber).
  • Spandex is used in filament form.
1961
POLYOLEFIN/
POLYPROPYLENE:
  • The first commercial production of an olefin fiber manufactured in the U.S. was by Hercules Incorporated.
  • In 1966, polyolefin was the world's first and only Nobel-Prize winning fiber.
1989
MICRO FIBERS/
MICRODENIER:
  • The first commercial production of micro fiber in the U.S. was in 1989 by E. I. du Pont de Nemours & Company, Inc. Today micro fibers are produced in a variety of synthetic fibers (i.e. polyester, nylon, acrylic, etc.)
  • The true definition of a micro fiber is a fiber that has less than one denier per filament. Micro Fiber is the thinnest, finest of all man-made fibers. It is finer than the most delicate silk.
  • To relate it to something more familiar--A human hair is more than 100 times the size of some micro fibers
1993
LYOCELL:
  • The first commercial production of lyocell in the U.S. was in 1993 by Courtaulds Fibers, under the TencelĂ‚¬ trade name.
  • Environmentally friendly, lyocell is produced from the wood pulp of trees grown specifically for this purpose. It is specially processed, using a solvent spinning technique in which the dissolving agent is recycled, reducing environmental effluents.

LMW Card Sliver System

Lakshmi Machine Works Ltd, manufacturers of the entire spinning range of machines offers the following products in Card Sliver System:
Gentle Blowroom Line: Encompassing the following products -- Bale Plucker LA23/S, Vario Clean LB9/2, Unimix LB7/4 and Flexiclean LB5/6.
The Gentle Blowroom lines are configured to meet the following requirements: Variable characteristics of cotton fibres; Higher productivity; Consistent quality which are achieved by: Gentle opening; Gentle cleaning; Effective micro dust extraction; Optimal blending. Thus, ensuring "Treating the fibres softly and gently and saving the raw material through less fibre loss".
New generation high production cards
New Card LC333 with Fine Feed Chute LA/I 6 and Card LC300A V3 with Fine Feed Chute LA/5 "Well carded is half spun." "Carding is the heart of Spinning." This clearly shows the vital role played by Cards.
The functions of the Card are: .
  • Individualisation of fibres thereby removing micro dust.
  • Dis-entanglement and minimizing neps.
  • To eliminate seed coat fragments and other contamination.
  • Better degree of opening and cleaning.
The Cards offered from LMW with distinctive configuration meets the above requisites. They form a package with the Blowroom line to deliver high quality sliver for the next process. These Cards are designed to suit every variety of cotton, man-made fibres and blends. New Card LC333 ensures high production of up to 120 kg/hr.
Bale Plucker LA23/S
Higher production up to 1,500 kg/hr; Working width of 2,300 mm; Auto scanning -- increases the machine utility and efficiency & elimination of skilled manpower; Automatic turning of head at any point of the track; Inverter & PLC controlled movements and positioning of plucking head; Double Plucking rollers.
Vario Clean LB9/2
Higher production up to 1,500 kg/hr; Integrated opening, cleaning & dedusting; Programmable grid adjustment & beater speed; Dynamic setting changes for different assortments.
Unimix LB7/4
Higher production of up to 800 kg/hr (600 kg/hr with opening and cleaning); Enhance the value of mixing through -- homogeneous blending, efficient opening and cleaning and flexible grid bar setting.
Flexi Clean LB5/6
Higher production up to 600 kg/hr; Variable production achieved by inverter drive controlled fibre feed for optimum opening and maximum cleaning efficiency.
Fine Feed LA7/5
Higher production up to 80 kg/hr per chute 1 or 2 assortments carded simultaneously in the same card group; Flexible assortment allocation of the cards (up to 10 cards per feeding machine).
Fine Feed LA7/6
Higher production up to 120 kg/hr per chute; High pressure feeding line and even compacting, in top-chamber; Feeding with spring loaded control plate; Wire mounted feed roller-inverter driven; Spiral pinned opening roller; Batt compacting by pressure in bottom chamber air releasing by finger plates.
LMW's new product in this range is the Card LC 333, which has the following salient features:
Higher Production up to 120 kg/hr; Triple Licker-in arrangement (Single Licker-in Optional); Specially profiled bottom cover; Aluminium alloy flats; Oscillating stripper to clean flats; Pressure regulated chute.